Basic HTML Version
R V T - P
RVT-P
Ducted heat recovery exchangers
– with increased resistance
The plastic RVT-P heat recovery exchangers
are special-design all-plastic recovery exchangers of the RVT
type
.
The RVT-P exchangers are suitable for ventilating
of galvanizing shop, agricultural areas with high ammonia
content, drying lines, chemical labs and plants, wet areas
with vapor generation, swimming pool halls, etc,
in temperature range of -25 °C to +80 °C.
.
The exchangers are inert against chemical compounds
at concentracions according to a table in the ATREA product
catalog.
2)
00 Pa.
3)
(min. G2 G4 )
4)
( . 2-
), a
5) To ensure cleaning of the recovery exchanger by water
flush (with a detergent) cleaning openings must
be installed in a duct (close to the flanges).
•
•
•
•
•
•
with high chemical resistance
500, 1000, 1500 and 2000 mm, in uniform
flange width module. The RVT-P exchangers can be supplied
in non-standard heights.
The RVT-P are standardly available in design (basic
recovery efficiency ) or
design (with increased recovery
efficiency).
1)
K/F
K/G
The exchangers may not be used for air with content
of organic solvents nor in an explosive environment.
Both sections of the exchanger must be connected
to the air-handling system equally, i.e. both must
be in positive or negative pressure with max. differential
of 6 The higher pressure must always
be at the fresh supply air side.
To protect the recovery core in both sections against dirt,
a recessed filter must be installed
to class
Install the recovery exchanger in moist and wet
environment in vertical position to ensure good
condensate drainage. Also, an automatic freeze protection
e.g step supply air fan speed control
nd condensate
drain via a trap should be installed.
high recovery efficiency
low pressure drop
low weight
low purchase cost
•
The heat recovery cores are assembled from thin sturdy
plastic plates which are stuck together to tight blocks
of height of
Blocks of the heat recovery cores are hermetically
assembled in a polyprophylene frame with threaded M8
holes to connect PVC ductwork
perfect exchanger tightness against short circuit
corrosion resistence in moist and chemical environment
minimum maintenance of the whole equipment
hPS
Rules for the RVT-P installation:
:
Features of the RVT-P exchanger
R V T - P - K
RVT-P-K/F,G 500
570
500
65
RVT-P-K/F,G 1000
RVT-P-K/F,G 1500
RVT-P-K/F,G 2000
RVT-P-K atypical
on reqest
1 070
1 000
80
1 570
1 500
94
2 070
2 000
120
Type
B
(mm)
B
o
(mm)
Weight
(kg)
685
795
55
55
alt.
alt.
B
o
B
685
795
55
55
35
35
Unit ventilators heat recovery
chapter 6.
issue
7
,
–
–
03/200
S E L E C T I O N S O F T W A R E
To select a heat recovery exchanger you
can use our special selection software.
Download it from our webpage
or contact us at our mail
d s
www.atrea.cz
ad res .
s a v e y o u r e n e r g y
466 01 Jablonec n. N.
C z e c h R e p u b l i c
U
N I T V E N T I L A T O R S & H E A T R E C O V E R Y D I V I S I O N
w w w . a t r e a . c z
A s.r.o., V Aleji 20
TREA
Fax:
+420 483 368 112
Phone:
1
+420 483 368 11
E -ma i l : atrea@at r ea . cz